Sign in perhaps register 。

laymanTable of several inches corresponding to welded pipe,

According to the national standard of hot rolled H-section steel in China (GB / t-,laymanA335p11 American standard high pressure alloy pipe, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.I-beam, also known as universal beam,laymanFinish rolled reinforcement manufacturer, After the above process, the next step is the polishing process of stainless steel pipe. There are network standards for internal and external wall finishing of pipelines, and the internal and external surface finishing of pipelines meets the mirror standard (i.e. sanitary standard).Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Cha-am,Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.

H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.In our daily life and work, we can often see a lot of steel products. At the same time, among many steel products, the figure of galvanized pipe is particularly prominent. This is because this kind of pipe will be applied to many engineering construction we often see in our life. There are also countless products processed with this kind of pipe. For example, in the field of mechanical equipment processing we often see, the application of galvanized pipe is more frequent. Let&#;s discuss the application scope of this kind of pipe today.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.market price,H-section steelAs shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.

I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.Where can I find it?, it has the advantages of low cost, and saves about % of the manufacturing cost of steel structure.Seamless pipeThe specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No. and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.layman,All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.According to the theory of steel structure, the I-beam flange should be stressed, that is, the I-beam should be standing rather than lying down. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the automatic control system will be upgraded.