Sign in perhaps register 。

Insert the pipe into the top of the bayonet,e the sleeve on the pipe to evenly apply the flux on the joint, and confirm that the pipe is inserted into the bottom of the socket, then wipe off the excess flux, and the joint is assembled and can be heated.However, it is difficult to change this situation too much in the short term. It is expected that the domestic strip steel price will mainly rise in the short term. It is reported that in order to pursue profits, Ltd. is currently increasing the supply of hot coils. It does not rule out that more steel mills in the future are inclined to one end of the plate in pursuit of profits or to lay hidden dangers for the decline. As far as tomorrow is concerned, the price may still maintain a narrow range of shock operation pattern.Vitti sur Seine, more and more steel plants have stopped production since October, and the production limit in Wu an and Tangshan heating seasons has been advanced. In addition,Vitti sur SeineH65 brass plate, the formal implementation of production limit in & quot; +& quot; urban heating seasons after November by steel enterprises, and the willingness to further replenish the inventory is not strong. In terms of supply, the fourth quarter is generally the peak period for the shipment of imported ores. Although the production of domestic mines has been reduced due to environmental protection, the quantity of * * * is relatively limited. In general, the short-term iron ore market may lack upward momentum.Qurghonteppa,First of all, we should set up a warehouse. The temperature in the warehouse should be generally kept at - ° C, while the humidity should be normal. The room should be kept ventilated.However, it is difficult to change this situation too much in the short term. It is expected that the domestic strip steel price will mainly rise in the short term. It is reported that in order to pursue profits, Tangshan Iron and Steel Group Co., Ltd. is currently increasing the supply of hot coils. It does not rule out that more steel mills in the future are inclined to one end of the plate in pursuit of profits, or to lay hidden dangers for the decline. As far as tomorrow is concerned, the price may still maintain a narrow range of shock operation pattern.After the pipe is cleaned, the welding flux and flux shall be immediately applied to the interface and the bayonet clearance. Sufficient flux shall be thinly coated on the mating surface and assembled immediately, so that dust and dirt will not pollute the capillary gap.

With the advent of heating season, steel mills in some regions began to implement the production restriction measures for blast furnaces in heating season, and the demand for iron ore was weakened. In addition, the production restriction policy was issued in Tangshan today. From : on October to : on October , the production restriction measures specified in this Notice were implemented.How to preserve the copper tube? In order to protect the excellent performance of copper pipes from the impact of the environment, we need to do the following: First, select appropriate sites and warehouses, and keep the surrounding environment dry and ventilated. Do not stack together with acid, alkali, salt, cement, etc.Red copper plate has ductility. Pure copper,Vitti sur Seine7075 aluminum pipe, which is as big as a drop of water, can be pulled up to two kilometers of thin wire or rolled into a transparent foil larger than a bed. The most valuable property of red copper row is that it has a very good conductive , second onlyver in common metals. But copper is much cheaper than silver, so it has become the & quot; protagonist& quot; of the electrical industry.Quality inspection report,Red copper plate has ductility. Pure copper, which is as big as a drop of water, can be pulled up to two kilometers of thin wire or rolled into a transparent foil larger than a bed. The most valuable property of red copper row is that it has a very good conductive , second onlyver in common metals. But copper is much cheaper than silver, so it has become the & quot; protagonist& quot; of the electrical industry.Among the three production methods of copper tube the oxidation method is the most. Because as long as the metal copper is oxidized by the anode and the copper ion of the anode is attached to the tube material, the copper tube can be produced. Thisthod is also the most common method to produce copper materials. It has not only been used for a long time but also has a mature technology, which is to produce copper tubes through oxidation reaction. This production method is the main production method of copper tubes in China.It has excellent conductivity, thermal conductivity, ductility and corrosion resistance.

Do not store too many other products, especially other acid materials and alkali materials, in the warehouse to prevent mutual reaction.Marketing Department,Advantages of red copper tube Durability: copper has stable chemical properties, integrating cold resistance, heat resistance, pressure resistance, corrosion resistance and fire resistance, and can be used in different environments for a long time.Copper pipes of different models shall be stacked separately.Strong connection firmness of copper pipe: the connection between copper pipe and copper fittings is strong.Vitti sur Seine,The room temperature tensile strength of the annealed red copper sheet is ~ kgf/mm, the elongation is ~%,Vitti sur SeineT2 copper plate, and the Brinell hardness (HB) is ~Safe and reliable: copper pipe combines the advantages of metal pipe and non-metal pipe. It is harder than plastic pipes and has the high strength of ordinary metals (the strength of cold drawn copper pipes is equivalent to that of steel pipes with the same waess); It is also easier to bend than ordinary metals has good toughness and high ductility, and has excellent anti vibration, anti impact and anti frost expansion properties.Generally, oxygen aylene is used as the gas source and LPG welding tool is used for heating. The torch of the welding tool shall face the joint and then continuously heat the whole joint. This will avoid excessive local heating.