Sign in perhaps register 。

When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know: Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Dimos iliopoli, Quality requirementsThe working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Tupiza,At the same height, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards.As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different,Dimos iliopoliQuotation of Q235 I-beam, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)

C-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc scar,Dimos iliopoliHow many kilograms per meter of welded pipe, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life,Plan option : Martensitic chromium alloy pipe,The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Greatly reduce the environmental pollution caused by abrasion, and increase the labor cost of material cleaning

I-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:Quality Assurance, Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties, specification scope, mold shell and software requirements, which are very simple very easy to be replaced, and relatively low product cost. The processing time is not long enough, the processing capacity is not high, the total length of processing pipeline is limited and the size of machinery and equipment is generally short. The zinc coating is thick, the crystallization is detailed,Dimos iliopoliHow much is a 6 meter 25 galvanized pipe, uniform and non porous, and the corrosion resistance is excellent; Small longitudinal crackDimos iliopoliUnder the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.The system is mainly composed of control box, finishing roller, pre leveling unit, finishing unit and straightening unit.Ways to obtain surface compressive stress characteristics of alloy tubes