Sign in perhaps register 。

　　 Then reinstall the equipment on the engine and install the rubber hose.　　Many users, including new practitioners of slurry pumps,　　 After the electric pump has been used for many times but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?Kavana, it is necessary to put the electric pump into clean water and run it for several minutes to prevent sediment in the pump and ensure the cleanness of the electric pump.　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron,KavanaIrrigation deep well pump, and infiltrate tin evenly.Viljoenskroon,　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, which leads to accumulation　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is

　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment　　 Assembly of electric pump: assembly sequence of motor: stator assembly → lower guide bearing assembly → rotor assembly → thrust disc → left nut → thrust bearing assembly → base assembly → upper guide bearing seat assembly → skeleton oil seal → connecting seat. Adjust the studs so that the motor shaft extension meets the specified　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Process inspection,　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.

　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.Marketing Department,　　The application of pumps involves all aspects of work and production,KavanaCentrifugal slurry pump, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　 When the slurry pump operates it rotates at a high speed, and the components of the slurry pump have a heavy weight. Therefore once it reverses,KavanaBooster pipeline pump, the force will directly push the impeller to the outside, and the impeller collides with the sheath and guard plate. If the speed is high, the force ratio is low　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.Kavana,　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.