Sign in perhaps register 。

　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any timeAugsburg,　　Slide evenly and slowly along the guide rail until the active coupling is in place. When the mobile device is selected,AugsburgWater well pipeline pump, the hose shall be sleeved first, and the chain rope shall be threaded into the two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.　　For example, in the market, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.Mponela,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.　　The hardened mud layer collapses after softening, it must be noted that if the fault is caused by electricity you can find the reasons from the above items. However the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, people who do not know electricity should not repair it by themselves, so as to avoid people　　Is the submersible sewage pump a submersible pump or a sewage pump QW (WQ) submersible non clogging sewage pump QW (WQ) submersible non clogging sewage pump: the pump adopts a unique single or double blade impeller structure, which greatly improves the sewage passing capacity and can effectively pass through times the fiber material and diameter of the pump diameter　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts,AugsburgVertical centrifugal slurry pump, make the bearing components move forward, and roll the shaft by hand to press theranking,　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.

　　Let the medium containing some solid particles generate a certain flow rate, so that the slurry can be transported. In terms of the principle of the submersible slurry pump,AugsburgLong shaft submerged slurry pump, it is actually quite simpleLet's see, it is necessary to replace the new impeller in time for use.　　Clean up the silt and other obstructions in or around the water pump.　　Rate loss, so shaft power = effective power + lost power.Augsburg,　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times air holes usually appear