Sign in perhaps register 。

Alloy tube is widely used in our daily life, which provides us with great assistance.→ I-beam can be processed into T-beam, and honeycomb beam can be combined to form various section forms, which greatly meets the needs of engineering design and manufacturing.Swarth,Galvanized pipes are designed to maintain high enough corrosion resistance.The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Essaouira, the moment of inertia of the two main axes of the section is quite different,SwarthHow much is a ton of high frequency welded pipe,SwarthHow much is 114 seamless pipe per ton, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Carburizing: carburizing is the process of penetrating carbon atoms into the surface layer of steel. It also makes the low-carbon steel workpiece have the surface layer of high-carbon steel, and then after quenching and low-temperature tempering, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into - - and - according to different specification numbers. The length selection range of imported I-beam is generally -.

Stages needing attention in the production and manufacture of alloy tubesHowever, compared with plastics, these pipes, like other metals, remain stable and will not be affected by high temperature.The system is mainly composed of control box, finishing roller, pre leveling unit, finishing unit and straightening unit.Price,Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materials The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions,Swarth80 seamless pipe price, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.

In order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.Where to sell API,H-section steelDuring the heating and cooling process of structural welded pipe workpiece, due to the inconsistent cooling speed and time of surface layer and core layer, the temperature difference will be formed, resulting in uneven volume expansion and contraction, resulting in stress, namely thermal stress. Under the action of thermal stress, the starting temperature of the surface layer is lower than that of the core layer, and the shrinkage is greater than that of the core layer, making the core layer stretch. At the end of cooling, the surface layer is compressed and the core is stretched because the cooling volume contraction of the core cannot be carried out freely. That is, under the action of thermal stress, the surface of the workpiece is compressed and the core is pulled.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams.Swarth, high precision and small residual stress. It does not need expensive welding materials and weld detection it has the advantages of low cost, and saves about % of the manufacturing cost of steel structure.I-beam has wide flange, thin web, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.