Sign in perhaps register 。

Wooden wedges and nails shall not be used for fixing during construction.The contact surface between the wooden wedge and the nail is too small, and the grip strength of the nail is insufficient.Bones are easy to loosen, they are closely combined, but there is a small groove, which is called U-shaped groove in the industry. In most cases, this kind of plate is reinforced floor.One of the great advantages of the molded plate is that it is easy to clean. It is very convenient to clean the dust in the small ditch, as long as you wipe it with a rag or mop.Le Mans,Third, strong wear resistance. SmellVucitrn,The combination of hardness and softness.The wood floor in the living room should be made of boards without knots, cracks and mildew. Generally, Fraxinus mandshurica, camphor and teak are better because their lines are beautiful and clear, and their texture is moderate.The laying method of wooden floor is not very difficult, but it is required to have a certain carpentry foundation.Firstly, the wood board shall be processed into the length and width coordinated with the room size according to the room size, and the floor shall be cleaned before laying.When laying draw the center point and vertical and horizontal vertical lines of the room,Le MansWhat is waterproof, and lay from the center to the four sides. glue and an appropriate amount of cement can be used for bonding between laths.Note that the glue must be coated evenly to avoid the warping of the plate.The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary, the cost is much higher if the number of wear-resistant revolutions is high.If the new floor is to be sent to a room equipped with large equipment, it may need to be rewired before moving.Make sure to contact an electrician before installing the floor.If the equipment needs to be moved, there is no need to worry that the heavy machinery will scratch it before installing the old floor.Keep tarpaulin and tape.

I like to choose soft floor leatherCompared with laminate flooring: pattern non laminate flooring.Comparison with solid wood flooring: strong glue must be selected for the production of solid wood composite flooring. Unlike the traditional solid wood flooring, only the wood itself is basically with glue.Although the environmental protection quality of super glue is very high, and the formaldehyde concentration can be basically ignored, it still exists.Second specifications and models.When purchasing solid wood multi-layer wood flooring, many customers like to choose wide and long double-layer solid wood flooring. They feel that the really raised flooring looks level and atmospheric at home.In fact, the longer the better the floor, it will endanger the reliability of double-layer solid wood floor.The length and total width of solid wood multilayer wood floor should be short, not suitable for long, narrow, not suitable for wide.retailer,Fourth, it is mainly the veneer thickness (decorative board thickness). The multi-layer solid wood floor has ,-, and the new three-layer solid wood floor has , to , mm.SPC floor has several advantages: imitation of water, imitation of fire, anti oil stain, can replace ceramic tile and wood floor.Applicable to all major tooling and home decoration.For example, hospitals, schools, hotels, hotels, restaurants and other places.After the solid wood floor is transported to the project installation site, it shall not be unpacked and installed immediately.After unpacking, it must be kept indoors for more than one week.The solid wood floor can be used only after it is adapted to the temperature and humidity of the room.

The surface is treated with special technology, without air holes and water impermeability. It is no problem to shop in the areas where toilets and kitchens communicate with water.No, it will not be like the ordinary wooden floor. Once it bubbles, it will deform and bubble,Le MansDoes laminate need maintenance, or it will become moldy due to high humidity.Welcome calls , Never soak the floor with water during use. If there is an accident, mop the floor with a dry mop in time.PVC floor is generally between mm and mm thick, and the net weight per square meter is about -kg, it has incomparable advantages of load and saving indoor space.In addition it has unique advantages in the renewal and transformation of old engineering buildings.The core layer of WPC wood floor is thicker than that of SPC floor.WPC boards range from to mm, while SPC boards range from to mm.Le Mans, Super durable.The surface of stone plastic floor has a special transparent wear-resistant layer processed by high technology, which is super wear-resistant.Therefore, stone plastic flooring is becoming more and more popular in hospitals, schools,Le MansSPC floor wear resistance, office buildings, shopping malls, supermarkets, vehicles and other places with large flow of people.I have seen the evaluation video before. Netizens rub the steel ball of cleaning tableware back and forth on the SPC floor, I think it&#;s not like it anymore. You can see how good its wear resistance is.Some customers want to take a lighter to light the SPC floor to see if it can burn. If it burns it is not fire safety, and if it doesn&#;t burn, it is flame retardant.In fact, and the flame retardant raw materials are listed as class a fire safety according to the national standard, such as marble, wall tiles, etc.The technology of Class B flame retardant grade includes mm diameter cotton wool, sprinkled with ethanol, and placed on the PVC latch floor for natural ignition. After the cotton wool is burned, accurately measure the diameter of the burned PVC latch floor impression. If it is less than mm, it is Class B flame retardant grade.Instead of watching it burn.