Sign in perhaps register 。

　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　If there are sundries blocked, the pump will not be filled with water. When this happens again,AitosWear resistant slurry pump, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,Aitos, this is also due to the accumulation of more than years of history. The evolution of pumps here is relatively diverse. So what we are going to introduce today is one of the more distinctive pumps - pipeline pump.　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well, which should be a comprehensive optimization design method.Rafsanjan,AitosHH slurry pump,　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　 If the pump is equipped with a vacuum gauge or pressure gauge, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.

　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and a special person is required to control the shutdown of the water pump.　　Causes: there is air or gas accumulation in the water inlet pipe of the pump so it is usually used temporarily without an electric control cabinet, or the bottom valve is not closed tightly, the water supply is not satisfied,AitosSubmersible non clogging slurry pump, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.Latest quotation,　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular

　　How to avoid this situation when the equipment is in use.Marketing Department,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　 when the deep well pump is put into water for use, pay attention to protect the cable. The cable must not be stressed to prevent damage. The lifting weight of the lifting device (such as tripod, hoist or electric hoist) used shall be greater than the weight of the submersible pump, and enough space shall be reserved. A wood that is tied to the wellhead with a rope　　There will be no insufficient liquid supply or other problems.Aitos,　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly the water supply is not satisfied, and the gate valve or flap valve is not closed tightly.　　In addition the packing of the vacuum pump leaks seriously, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.