Sign in perhaps register 。

　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.Trojans,TrojansSubmersible non clogging slurry pump,　　The discharge side of the pump must be equipped with a valve (ball valve or stop valve, etc.) and a check valve. The valve is used to regulate the operating point of the pump. The check valve can prevent the pump from reversing when the liquid flows back (the long shaft deep well pumps produced by our company are equipped with anti reversing check devices) and prevent the pump from being hit by water hammer　　During normal operation, some even as high as ℃. In this case, orMagnifier one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating,　　So it is called: submersible slurry pump.　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating

　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump　　 Pipeline high-temperature oil pump, pipeline high-temperature chemical pump, pipeline high-temperature hot water pump. These models are designed to be formed on the basis of adding water cooling units, and the operating temperature can be as high as degrees or higher.　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, shape, hardness, concentration, acid alkali and other characteristics of the transported materials.Test conclusion,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　It is not correct that it has no effect on us.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.

　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.quality index,　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.　　 Before using the pump, carefully check whether the cable is damaged, whether the fasteners are loose or fall off, and whether the pump is deformed or damaged during transportation, storage and installation.　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support,TrojansISG single stage vertical pipeline pump, if there is a problem with the clearance in the future use,TrojansVertical slurry pump, loosen the support clamp first and say that the nut is looseTrojans,　　Work, no noise and vibration, and the site is cleaner.　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.