Sign in perhaps register 。

FokaZD slurry pump,

　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.Foka,　　The ball or bearing of the motor is damaged.　　After meters the sealing of the equipment can not bear the water pressure at this depth.Uong Bi,　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, shape, hardness, concentration,FokaVertical non clogging sewage pump, acid, alkali and other characteristics of the transported materials.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, close the cock connected with the submersible slurry pump before starting the motor we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller

　　 If the pump is equipped with a vacuum gauge or pressure gauge, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　 whether pre lubrication water tank is required　　During adjustment, firstly loosen the support cover, then compress the nut, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationPrice,　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areas

　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Honesty is the foundation,　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.　　 No maintenance: if it is not used continuously after startup, the submersible pump will rust and cannot be started. If it is not used for a long time, do not immerse it in water for a long time. Put it into clean water and run it for a few minutes to clean the mud inside and outside the pump.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.Foka,FokaQuotation slurry pump,　　Promote the continuous expansion of the sales network group.　　The utility and durability of the utility model so the polymer composite materials are generally used in production.　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.