Sign in perhaps register 。

The current woodworking is basically done by woodworkers. The 'general woodworking' method is adopted, and the shrinkage joint size is not calculated according to the thermal expansion and cold contraction parameters provided by SPC flooring factory.If the room is slightly larger, but the reserved gap is too small, especially when the temperature difference between winter and summer is too large, it is very easy to have no gap to expand, resulting in arching and warping.In particular, the previous agency said that the laminate floor is a waterproof floor, which is only the surface layer. In fact, the only taboo in the application of laminate floor is small blisters.Auorburg,Keep the floor dry and clean. It is clean. Do not wash it with water to avoid long-term immersion of the floor.For oil stains, use mild neutral detergent and wash with warm water in time to avoid the corrosion of alkaline water and soapy water on the ground, and do not wipe the ground with gasoline or other high-temperature liquids.The double composite solid wood floor adopts double-layer solid wood pressing. It feels like pure natural wood. The installation and maintenance is very simple. It is suitable for floor heating, beautiful and generous, good reliability, and contains a small amount of indoor formaldehyde.Madang, SPC floor adopts marble powder and new materials, which is more green and environment-friendly.The cost of stone plastic floor is quite low, and it can be flame retardant. It has no affinity with water and is not easy to mildew. Stone plastic floor has sound-absorbing effect, so we don&#;t have to worry about the sound of high-heeled shoes hitting the ground anymore.Characteristics of fake and shoddy laminate flooringSPC floor is mainly made of calcium carbonate, including pur Crystal Shield transparent layer wear-resistant layer, color film layer, SPC polymer rural base and soft sound insulation rebound layer.Its foreign home decoration sales market is very hot, which is not suitable for too low or too high.SPC floor does not use strong glue in the production process, so there are no indoor formaldehyde, benzene and other harmful substances.The indoor formaldehyde emerald green floor is not easy to cause damage to the body.original,Headache, dizziness, fatigue, nausea, vomiting, nausea,AuorburgWaterproof board factory, chest tightness, eye pain, sore throat, stomach pain, palpitation, shortness of breath, insomnia, weight loss, memory loss, autonomic nerve obstruction, etc.Long term inhalation by pregnant mothers is likely to cause abnormal fetuses and even death.The flame retardant grade is B, and the indoor formaldehyde is higher than the national standard.Defects of solid wood composite floor

The crystal surface is basically flat. It&#;s easy to take care of and clean up.query, Wear resistance, wear resistance grade t.Because the base material of the solid wood reinforced composite floor adopts multi-layer veneer composite, and the wood fibers are crisscrossed into a network superposition combination, which makes the internal stresses of different wood adjust each other between layers, ensures the smoothness and stability of the wood floor, and maintains the beauty of the solid wood floor. It can not only enjoy the natural warmth,Small blisters can not be repaired after damage, and the upper foot is weak.In fact, it is very simple to prevent wood floor cracking. Usually, do a good job in floor maintenance and humidification of wood floor in areas with low average moisture content, which can be effectively prevented,AuorburgComplete collection of floor leather, or raise flowers and fish at home, and put buckets in the corner of the room.Generally speaking, most of the strengthened solid wood composite floors are up to standard commodities within the scope of standardized formaldehyde emission.According to relevant requirements, the formaldehyde emission of commodities in the room shall be class E, i.e. ≤ mg/l.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth,AuorburgCement waterproof board, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, cut with a cutter along the ruler then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.