Sign in perhaps register 。

　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.Feldkich,　　There is a blockage in the water pump.　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flowspoland,　　Commodity.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, so　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation

　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　In fact,FeldkichBooster pipeline pump, as far as whether the vertical pipeline pump has a suction lift is concerned, we can tell that it has a suction lift. But what you need to know is that suction range and self-priming are actually two different concepts.　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willproduction costs,　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other,FeldkichSubmersible sewage pump,FeldkichZD slurry pump, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water

　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.discount,　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　 Check whether there is a problem with the ventilation system: check whether the fan is damaged, whether the fan rotates correctly, and whether there are abnormal objects blocking the ventilation holes.　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well, which should be a comprehensive optimization design method.Feldkich,　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, so there will be no buried pump when it is used. However　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.